Parts & Accessories

Replacement bearings for Stan's NoTubes Neo hubs. Includes 2 bearings. - 26mm OD x 15mm ID - 7mm thick

Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place

Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs - SealLock end caps feature a low friction U-cup seal that snaps into place

Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's Standard Tubeless Kit converts standard tubed wheels to tubeless so you can reap the benefits. Everything you need to go tubeless is included. Plus, you won't miss dealing with flat tires and you'll save money on tubes!

Stan's Threaded Valve Extenders let you convert deep-section rims to tubeless. They're precision-machined from aluminum and are designed to fit deep-dish carbon and aluminum rims. And, they're threaded on the outside so you can install the Presta lock-ring nut for a perfect seal.

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Lay down Stan's Universal Kit Rim Tape before the tubeless conversion of your non-Stan's rims. It makes your rims air tight and ready for tubeless use by covering the spoke holes.

- Cassette Body Type: Shimano/SRAM 11 Speed Road - Material: Steel

The Deadbolt Ultralight Thru-Axles are offered in a 6mm flat button-head design, for a flush, clean look. Lightweight, easy to use, and secure. - CNC-machined from 7000 series aluminum - One-piece design - Designed to fit all current Salsa thru-axle frames - For other frames, check with the manufacturer for compatibility and other specifications - 6 mm hex wrench required for installation

Salsa springs for Flip-Off skewers

Keep your skewers properly situated with these quality skewer springs from Salsa.

These MTH 716 Conversion Caps allow your SRAM MTH 716 front hub to accept a 15 x 100mm thru-axle.

- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T

The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.

Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork.

Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork. Kit includes Center Lock Adaptor, allowing riders to use 6-bolt rotors on Shimano Center Lock compatible hubs. - 10mm spacer kit adapts 100 x 15mm front hub to 110 x 15mm - Includes 10mm adapter to 6-bolt rotors - Includes external spline lock ring for thru-axle compatibility

- Flanged 15mm axle nuts - Durable chromoly construction - Spacing / Axle: B/O

Origin-8's Track Cog Lock Ring with left-handed threading and 1.29 x 24tpi in a chrome finish completes your basic track cog locking needs.

V2 Tubeless valves are stronger, lighter, and even easier to use thanks to the machined aircraft grade 7075 aluminum and Muc-Off's new Tire Insert air ?ow system. The new design features six slots that are machined into the base of the valve stem, allows tubeless sealant ?uid and air to ?ow freely, even when running tubeless tire inserts. - 7075 Machined Aluminum valve stem and cap - Tire Insert air flow system keep air moving freely and compatible with most tire foam inserts - 4mm machined Allen Key slot for easy installation and removal - Includes Valve Core Removal Tool (integrated into spare alloy cap) - Supplied with various rubber bases to optimize fit with multiple rim types

Mavic's XD freehub body is compatible with all Crossmax and Deemax wheels (2012 and after) or all wheels using TS-2 hubs. This freehub body converts a rear wheel to work with SRAM's XD standard, making the wheel compatible with the XX1 drivetrain. Two kits are available : XD freehub body ITS-4 and XD freehub body TS-2, each with hub-specific parts.

These lightweight valves help prevent clogging from tubeless sealant. - Aluminum - 40mm length

Replacement freehub kit for Hydra hubs

Your riding doesn’t need to stop when the weather gets cold. Features - Giant road thru-axle trainer axle - Alloy construction - For use on 2017+ Giant road bikes with a 142x12mm rear thru-axle

Grade 10 chromium steel balls

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.